How to String a Winter Pool Cover
Thread the cable through the cover's grommets all the way around the pool, hook it into the winch, then tighten until the cover sits snug against the top rail. String it before you do anything else on closing day, while the cover is still easy to reach.
On this page (9 sections)
- What you need before you string a winter pool cover
- How do you thread the cable through the grommets?
- How do you tighten the winch without overdoing it?
- How do you secure the loose cable end?
- Where does the winch and cable go on a deck or partial deck?
- What else holds the cover down once it's strung?
- Which cover should you buy if your cable setup is worn out?
- How do you string the cable on an oval or irregular pool?
- How do you know the cover is strung correctly?
Stringing a winter pool cover means running the cable through every grommet around the edge, fitting it into the winch, and tightening it until the cover sits snug and even on the pool. Do this step first when you close the pool, because the cover is easiest to handle before water, ice and debris pile on top.
A snug cable is what keeps wind from getting under the edge and lifting the cover. The method is the same on most round and oval above ground pools, and it takes only a few minutes once you know the order of steps.
What you need before you string a winter pool cover
You need the cover, its cable and winch, and a clear top rail to work around. Most winter covers ship with the winch and cable included, so check the box before you buy anything extra.
Lay the cover out on the pool first and center it so the overlap is even all the way around. A cover with a 4 foot overlap leaves more material to work with than one with 2 feet, which makes this step easier.
Clear the top rail of leaves, toys and sharp edges before the cable goes on. A rough spot under the cable can wear the cover edge through the winter.
If you're still choosing a cover, our guide to the types of pool covers covers winter, solar and safety styles. For an above ground pool, a solid winter cover with a cable is the usual starting point.
How do you thread the cable through the grommets?
Feed one end of the cable through the grommets in order, all the way around the pool, keeping the cable on the outside of the cover edge. Work in one direction so the cable doesn't twist.
Start at the spot nearest the winch position and push the cable through each metal grommet in turn. Grommets are spaced around the perimeter; on the 28 ft Shop Square cover they sit about 30 inches apart.
Keep the cable flat against the cover as you go. If it starts to kink or spiral, pull it back and straighten it before continuing.
Leave a short tail free at the start so you can reach it once the cable comes around. Don't pull the cable tight yet; the cover should still sit loosely on the water.
What if a grommet is torn or missing?
Skip a damaged grommet only if the cable still runs smoothly around the rest of the edge, and treat the cover as weaker at that point. A torn grommet can let the cable pull free in a winter storm.
Don't punch new holes in the cover to replace a grommet. That opens the material to tears and lets water through a solid cover.
If more than one or two grommets are damaged, a replacement cover is the safer buy. A cover with intact grommets and an included winch, like the Robelle below, avoids the problem.
How do you tighten the winch without overdoing it?
Fit the cable end into the winch and crank slowly, checking the edge every few turns. Tighten until the cover sits snug against the top rail, then stop.
A winch pulls the cable in small steps. Turn the handle a few times, walk the perimeter, and pull the edge down by hand where it still looks loose.
Keep the cable in the same channel all the way around so the tension is even. If one side looks tight and another loose, loosen the winch and re-seat the cable before cranking again.
Stop when the cover no longer flaps when you lift it slightly at the edge. More tension isn't better: it strains the grommets and the cable itself.

A solid cover with a 4 foot overlap and an included winch and cable, so the stringing step is ready to go out of the box.
See it on AmazonHow do you secure the loose cable end?
Wrap the free tail around the cable a few times and tuck it under the tightened run so it can't whip in the wind. A loose end can work the winch loose over the winter.
Check that the cable sits in the winch's channel and the handle is folded flat. Anything hanging off the edge catches wind and can pull the whole cable open.
Once the cable is tight and the tail is tucked, the cover's edge should sit flat and even. A cover that rides up on one side means the cable needs re-seating.
Where does the winch and cable go on a deck or partial deck?
Run the cable around the pool's perimeter and under the deck where it can, then set water weights on top of the cover over the deck sections. This keeps the cover down without drilling into the deck.
For a full deck, the cover sits on top of the deck and water weights hold it in place. The cable still runs around the cover edge, but the weights do the main holding over the deck.
For a partial deck, the winch and cable go around the pool perimeter and the cable runs under the deck where there's room. Water weights go on the cover over the deck side.
Don't string the cable through deck boards or rail fittings. The cable is meant to close the cover edge, not to anchor the cover to the deck.
What else holds the cover down once it's strung?
Cover clips and a cover wrap add grip on windy sites, and an ice equalizer pillow helps the cover ride the freeze and thaw. These are extras, not replacements for the cable.
Clips snap over the top rail and hold the cover edge down between grommets. A cover wrap runs around the pool and adds a second layer of hold on exposed sites.
An ice equalizer pillow goes in the water under the cover. It gives expanding ice somewhere to push instead of straining the cover, and the Robelle cover lists it as sold separately.
Skip these extras on a sheltered pool where the cable already holds the edge flat. Add them where winter wind is strong or the pool sits in the open.
Which cover should you buy if your cable setup is worn out?
Buy a cover whose winch and cable come in the box, so you don't have to match a new cable to an old cover. Check the grommet spacing and the overlap before you order.
The Robelle 24 ft Super Winter Pool Cover is the pick for most round above ground pools here. It's a solid cover with an 8 x 8 scrim and 2.36 oz per square yard polyethylene, plus the winch and cable included.

A lighter round cover with reflective strips and ground nails, for a smaller pool that needs night visibility.
See it on AmazonThe UIRWAY 18 ft cover uses 420D silver material with reflective strips and luminous ground nails. It has a full circle of webbing and a drawstring instead of a steel cable, so the closing method differs from a winch cover.

A 28 ft round cover with a vinyl-coated cable and winch for a bigger above ground pool.
See it on AmazonThe Shop Square 28 ft cover fits larger round pools and comes with a vinyl-coated cable and tightening winch. Its grommets sit 30 inches apart and its seams are heat-sealed.
When your pool has a deck or you want the extra safety of a tensioned cover, read safety cover vs winter cover before you decide. The best fit for most above ground pools in this group is the Robelle 24 ft, because the included winch and cable make the stringing step simple from day one.
How do you string the cable on an oval or irregular pool?
Follow the grommets in order around the edge, even where the pool curves back on itself, and keep the cable flat through each turn. The order matters more than the speed.
On an oval pool, the cable passes through more grommets per side and has to follow the ends closely. Feed it slowly around the curves so it doesn't cross over itself.
On an irregular pool, walk the perimeter with the cable as you feed it. A cable that skips a grommet leaves a gap where wind can lift the edge.
If the cable is too short to close the loop, the cover size is the issue, not the technique. Move up a size rather than forcing or splicing the cable.
How do you know the cover is strung correctly?
The cover sits flat on the water with an even overlap all around, the cable runs through every grommet in one direction, and the winch holds it snug without strain. Check these before you add weights or clips.
Look at the edge from a few spots around the pool. A correct string job leaves no slack spots and no tight spots, and the cover doesn't pull up at any grommet.
Check the winch handle sits flat and the cable tail is tucked. A dangling tail or a loose handle is the usual cause of a cover that comes apart in the first big wind.
Once the edge is even, add your water weights or clips and you're done with the stringing step. If this is your first closing, how to install a winter pool cover covers the steps before and after the cable.
For a bigger pool, our round-up of the inground pool covers for winter covers the options that suit a larger footprint.
Frequently asked questions
Can I string a winter cover without a winch?
Some covers use a drawstring or webbing instead of a steel cable and winch. Follow the closing method that came with your cover, because a cable without a winch has no way to stay tight and can slip loose in wind.
Should the cable run over or under the top rail?
Run the cable through the grommets at the cover edge and snug it against the outside of the top rail on a traditional above ground pool. With a partial deck, the winch and cable go around the perimeter and the cable runs under the deck where it can.
How tight should the cable be?
Tight enough that the cover doesn't flap or lift at the edge, and no tighter. Over-cranking strains the grommets and the cable, so stop when the edge sits snug and even all the way around.
Do I need cover clips or water weights too?
Often yes. A cable holds the edge down, but clips or a cover wrap add grip on windy sites, and water weights sit on top of the cover where the pool has a deck.
Check what your cover's closing instructions call for.
What should I do if the cable won't reach around the pool?
The cover is probably too small for the pool, since the cable is sized to the cover's perimeter. Don't stretch or splice the cable; move up a cover size so the cable can close all the way around without force.
About this guide: Our look at stringing a winter pool cover draws on maker specs, materials and what owners report. See how we research.



